Counter

• Display Type: Digital
• Display Digit: 4 / 6 digit Single / Dual
• Settings: Membrane Keyboard
• Count mode: Up / Down
• Input Type: Proximity / Potential free Contacts
• Output: Up to 3 Relays
• Battery Backup: Optional Optical Encoder / Quadrature

• Display: 4 / 6 digit Single / Dual
• Settings: Membrane Keyboard
• Count mode: Up / Down
• Input: Proximity / Potential free Contacts
• Output: Up to 3 Relays. More relays possible.
• Battery Backup: Optional Optical Encoder / Quadrature
• Prescaling: Optional. Multiplying / dividing constant programmable
• Reset: External Manual / Auto / Programmable time
• Other Options: External Start / Stop / RS232 / Modbus Connectivity

• Display Type: Digital
• Size: 96 x 192 mm
• Depth: 100 mm
• Dispensing Capacity: Four to Six drinks
• Quantity: 200 ml, 250 ml, 300 ml

• For programming dust proof membrane keypad is used
• Highly reliable circuitry microcontroller based
• Supports Four to Six drinks
• Supports three volumes dispensing is supported
• For three volumes three independent start switches
• Automatic time setting option. From keyboard finer adjustments can be done
• Six digits counter each for six drinks and three volumes
• High accuracy and repeatability of timing as crystal controlled clock
• Irrespective of power conditions permanent count storage
• All this in a very compact size of 96 x 192 mm depth 100 mm
• Time is to be set for only one volume. Timings for other volumes calculated automatically

• Application: Industrial
• Display: 4 / 6 digit Single / Dual
• Settings: Membrane Keyboard
• Count: Up / Down
• Output: Up to 3 Relays
• Connectivity: External Start / Stop / RS232 /Modbus
• Scaling: 0.000001 to 999999

• Display: 4 / 6 digit Single / Dual
• Settings: Membrane Keyboard
• Count Mode: Up / Down
• Input: Proximity / Potential free Contacts Optical Encoder / Quaderature
• Output: Upto 3 Relays. More relays possible.
• Battery Backup: Optional
• Prescaling: Optional. Multiplying / dividing constant programmable 0.000001 to 999999
• Reset: External Manual / Auto / Programmable time
• Other Options: External Start / Stop / RS232 /Modbus Connectivity

• Display: 4 / 6 digit Single / Dual
• No of lines: 2
• Lightning Colour: Red
• Count: Up / Down
• Connectivity: External Start / Stop / RS232 /Modbus

• dimensional accuracy
• easy installation
• low maintenance

• Application: Industrial
• Display Digit: 6
• Count Mode: Up / Down
• Output: Up to 3 Relays
• Scaling: 0.000001 to 999999

• Less power consumption
• Quality Checked
• Sturdy design

• Display Type: Digital
• Dispensing Liquid: 4 - 6 different drinks
• Panel Size: 96 x 192 mm
• Dispensing Quantity: 200 ml, 250 ml, 300 ml
• No of Buttons: 3
• Display Digit: 8

• Microcontroller based highly reliable circuitry
• Dustproof membrane keypad for programming
• Supports three volumes for dispensing
• Supports four to six drinks
• Three independent ‘start’ switches for three volumes
• Auto mode to set timings
• Finer adjustments can be done from the keyboard
• Time is to be set for only one volume. Timings for other volumes calculated automatically
• High accuracy and repeatability of timing as crystal controlled clock
• Six digit counters each for six drinks and three volumes
• Permanent count storage irrespective of power conditions
• All this in a very compact size of 96 x 192 mm depth 100 mm

• Type: Automatic
• Display: 4 digit x 2 row LED display
• Output: Two Relay of 230V / 5A
• Mode of control: Auto / Manual
• Size: 96(W) x 96(H) x 150(D) mm

• microcontroller based digital circuitry
• 4 digit x 2 row led display
• dustproof membrane keypad
• proximity / optical encoder input for rotation length sensing
• two relay outputs rated 230v / 5a for forwarding and reverse motor control
• counts programmable
• automatic motor switching on counts
• auto / manual mode of control
• nicd rechargeable battery backup for count in case of power failure
• number of cycles programmable
• size 96(w) x 96(h) x 150(d) mm

• Display Type: Digital
• Display: 4 / 6 digit Single / Dual
• Count Mode: Up / Down
• Output Mode: Up to 3 Relays
• Output: 4 - 20 mA

A Counter is a device which stores and displays the number of times a particular event or process has occurred, often in relationship to a clock signal. It is a semiconductor device that is used for counting the number of times that a digital event has occurred. The counter's output is indexed by one LSB every time the counter is clocked. Our counters can count the number of products produced from the external pulses and can keep track of on and off timings and store the data in memory as per shift timings.

Technical Specifications:
•Display: 4 / 6 digit Single / Dual
•Settings: Membrane Keyboard
•Count mode : Up / Down
•Input : Proximity / Potential free Contacts
•Output: Up to 3 Relays. More relays possible.
•Battery Backup : Optional Optical Encoder / Quadrature Prescaling : Optional. Multiplying/dividing constantly programmable
•Reset : External Manual / Auto / Programmable time other Options: External Start / Stop / RS232 / Modbus Connectivity

Variations of Counters
Preset Counters:
Preset counters count to a preset number and give an output. Most of these counters can count up to or down to the predetermined number programmed through the counters keypad. Scaling is also available on some units. The outputs usually can be held until reset or auto cycling. Typical applications include dispensing machines, coil winding machines, portable equipment, ticket machines, production machines, wire cutting, length measurement and numerical positioning.

Length Counters or Multiplying counters or Pre-scaling Counters:
This length measuring counter records length in feet and inches and includes two rubber wheels. These are used for measuring revolving / rotating objects such as winding applications to measure the length of wire/length of paper/length of yarn etc. The scaling factor is user programmable to get the length in required units directly.

Batch Counters:
In industry many times a batch contains a certain number of objects. Batch counters will automatically generate a relay output when a preset number of count has reached and a number of such batches are also counted and stored in counter memory.

Counter with Totaliser / Ratemeter:
These counters are best suited to production output quantities, length, distance, time or anything that can be numerically related to a given operation that is critical. The Counter detects input impulses for the rate per second, minute, hour or days.

Production counters:
Production counters are large numeric static counters that display current counts under operator count up and countdown control. Perfect for line productivity monitors, next serving counters, stock tracking, etc.

Sequential Counters:
A sequential counter is one whose output bits change state simultaneously, with no ripple. The only way we can build such a counter circuit from J-K flip-flops is to connect all the clock inputs together so that each and every flip-flop receives the exact same clock pulse at the exact same time.

Up Down counters:
A counter that can change state in either direction, under the control of an up/down selector input, is known as an up/down counter. When the selector is in the upstate, the counter increments its value. When the selector is in the down state, the counter decrements the count.

Vending Machine Counter:
This is a special application for drink vending machines which are mostly installed to count the number of cups of a drink dispensed as well as to control the amount of drink dispensed. Our company offers dispensing counters which count the number of cups dispense for multiple flavours and also controls the amount of drink is to be filled in the glass.

• Application: Industrial
• Totalizer Display Limit: 9999 hours
• Connectivity: RS 232
• Size: 96 x 96 x 150 mm
• Led: Four / Six digit display

• Four / six digit display
• Real-time clock
• Time totaliser optional to indicate how long the machine has been running up to 9999 hours
• Machine on time / off time / power fail time / power on time storage
• External enable input for observing machine status
• Option to start time totaliser operation only when external pulses for counting are coming (factory set)
• Rs 232 for serial printer or pc connectivity
• modbus connectivity for retrieving data for factory-widescada / DCS applications
• Eclipse SCADA software optional for user-friendly report / spc data analysis etc
• All this in compact size of 96 x 96 x 150 mm